todo
Table of Contents
TO DO LIST
THINGS YOU CAN BRING THAT WOULD HELP
- “Shoe Box”-style plastic boxes. Nicer ones from Home Depot or even dollar store ones. We're not picky. If we had 20 of these show up, I'm sure we'd find a use for at least 20 more.
Next Makerspace Maintenance Punch List **(NO DATE YET)**
- Clear off main two tables, and refresh the paper tops (DO FIRST)
- Take garbage to dumpster (DO SECOND)
- Paint Marker an “MA” on tools that don't have it, so that they're easier to identify
- Reorganize green tool shelf - re-optimize cubbies to make more sense
- Go through the Pallet Racks a little bit - clean up/consolidate where possible
- Assuming some space is freed up here, move some extraneous things into it as “deep storage” (i.e. all but one of the totes of “wire bundles”, etc.)
- A general going-through of the shelves:
- Consolidate things that need to be consolidated
- Purge things that need to be purged
- label things that need to be labeled
General Space Infrastructure
- General cleanup (i.e. the kind of thing that should happen frequently- every week or three…)
- Empty garbage into dumpster (all of the cans, so we can fill them up again)
- Tidy all workbench surfaces
- Shelf organization/labeling
- Keep generally similar things together. If something's in the wrong place, get it to the right (or at least a right-er) place.
- Contain loose things into containers where possible
- LABEL BOXES/CONTAINERS/SHELVES: just use a piece of masking tape & a Sharpie.
- literally work on anything on the fixme list
- Sort bins of random stuff into where the random stuff actually goes
Shop Zone
- Tool organization - any improvements are welcome!
- Electrical wiring for the “new” 220V stick welder (convert its plug to something better? L6-30? - check with John K.?)
- Build a nice table add-on/fence for the Enco Drill Press?
Measure T-slot nuts for the Enco Drill Press. See of additional ones are available, or maybe make some.We had some, and then they may have disappeared. Re-check
"Hardware" Wall
- Fastener Organization & labeling
Electronics/Digital Zone (general)
Computers/Digital Fabrication
- Complete RepRap Snappy
- Make some kind of filament storage solution? (clear plastic tote w/holes & gaskets, and a bunch of color-changing silica gel??)
- Figure out steps needed to make the K40 Laser Engraver chooch safely & reasonably
- Move the surge strip powering that stuff to the front of the cart.
- Add an Emergency stop?
- Figure out water pump/alarm stuff (short version: water pump is running, but flow alarm is triggering? need better pump? replace alarm? right now alarm is shorted out in order to test functionality…)
Electronics
- Organize components better?
- Organize electronics tools better - electronics bench is a good start at this…
Figure out power supply pinout for prototyping station. - We have a picture of the pinout. Fabricobble a replacement or otherwise find one.
AV Stuff
- Figure out condition of donated microphones - parts needed? parts available?
This Wiki
- Update entries that need updating
- Delete entries that need to be deleted
- Add entries that need to be added (use the Tool Submission Form for Equipment)
- Add photos to Equipment entries? (Good for a first timer!)
- Add/Update instructions for Equipment entries
Miscellaneous
- Inventory First Aid supplies. Make list of recommended additions and/or replacements for anything missing.
- There are OSHA guidelines for what should be in one for various group sizes.
- Pallet Jack repair - if the right parts are identified, they can be ordered…
Long Term/Not any time soon
- More/better shelving?
- More improved use of vertical space? (not sure how to accomplish this without stairs/ladders)
- Any new shelving project should have a budget, rough drawing, and an explanation of where it will go…
todo.txt · Last modified: by sdh7